Emergency Power Control

SWX-EPC SERIES

Series Downloads

Overview

The SENSORWORX Emergency Power Control device provides a simple method of converting standard light fixtures into emergency light fixures for a UL924 compliant emergency application. Designed by LVS Controls, the SWX-EPC-2 family ensures compliance with both life safety and energy codes and eliminates the wasted energy that is used when emergency lighting is kept on 24 hours a day. These devices are typically ceiling or wall mounted in a junction box with a single gang plaster ring and are usually located in the area where the emergency fixtures are installed.

Basic Operations

All lighting fixtures (both normal and emergency) are controlled on and off (and/or dimmed) together during normal power operation by common lighitng control devices (i.e. switches, dimmers, occupancy sensors, daylight harvesting photocells, relay panels, etc.). However, during a utility power interruption, the SWX-EPC-2 will automatically bypasses the controls and override to on all the fixtures designated for emergency operation. With the dimming option, the unit can also ensure that controlled emergency lighting is returned to its full bright level.

The SWX-EPC-2 family also has a patented automatic diagnostic feature. When a room’s switch is turned off, the SWX-EPC-2 will run a 2.5 second self-test routine, verifying that the emergency power source is available and that the unit and connected fixtures are all functioning correctly. This feature eliminates the need for time-consuming and costly manual monthly testing and is approved for this purpose. This also allows the unit to be installed in remote or inaccessible locations, because the diagnostic feature does not rely on access to its manual test switch.

Features / Emergency Power Control

Features

  • Patented Automatic Diagnostics

  • Slim & Attractive Flush Mount Profile

  • Easy Front Access to Manual Test Switch

  • Integrates with Fire Alarm Systems for Override

  • Remote Test Configuration

  • Utility & Emergency Power Indicator LEDs

  • 0-10V & DALI Dimming Option

Specifications

Physical

SIZE
3.00”H x 1.70”W x 1.20”D
(7.62 x 4.32 x 3.05 cm)

MOUNTING
Single Gang Switch Box
4-11/16” Square Junction Box w/ Single Gang Mud Ring
Suitable for Installation in Plenum

LED INDICATORS
Red: Emergency Power Present

Green: Utility Power Present

MANUAL TEST BUTTON

Electrical

SENSING INPUT
120-240VAC/277 VAC

LOAD RATINGS
GENERAL PURPOSE & LED:
20A @ 120-277VAC

BALLAST LOAD:
20A @ 120-277VAC

INCANDESCENT LOAD:
1200W @ 120VAC
1500W @ 277VAC

RELAY TYPE
Normally Closed

DIMMING
0-10 VDC ballasts or drivers compliant with IEC 60929 Annex E.2

Environmental

OPERATING TEMP
32°F to 140°F (0°C to 60°C)

Single Line Drawings

Model: SWX-EPC-2

MODEL #: SWX-EPC-2-D

Wiring Diagrams

 

MODEL #: SWX-EPC-2 (Standard Configuration)

A common switch controls both normal and emergency lighting in a space. Upon loss of normal power, the emergency lighting comes on regardless of switch position.

MODEL #: SWX-EPC-2 (Shunt Configuration)

A dedicated switch controls emergency lighting in a space. Upon loss of normal power, the emergency lighting comes on regardless of switch position.

MODEL #: SWX-EPC-2-D

A common dimmer controls both normal and emergency lighting in a space. Upon loss of normal power, the emergency lighting comes on to full bright regardless of dimmer position.

REMOTE DIAGNOSTIC WIRING

To disable the remote diagnostic feature, cut the units blue jumper wire.

FIRE ALARM / REMOTE TEST SWITCH WIRING

The unit’s red low voltage jumper wire is an override input to connect in a fire alarm or remote test switch. For more information visit http://www.lvscontrols.com/assets/UL924FAI.pdf

Installation Options

Ordering Info

EXAMPLE MODEL # SWX-EPC-2-D
MODEL NUMBERDESCRIPTION
SWX-EPC-2Emergency Power Control
SWX-EPC-2-DEmergency Power Control w/ Dimming

Related Products

Ceiling Sensors

This sensor’s chase nipple attachment makes surface mounting to a finished ceiling simple and secure.

Wide View Sensors

With five contractor friendly mounting methods, locating a sensor in a corner has never been easier.

Power Packs

Mounting snaps and an optional low voltage wiring chamber make this power pack a breeze to install.

Design by DZYNR | ©2020 BLP Technologies, Inc. All Rights Reserved.