Wireless Fixture Controller
w/ 0-10V Dimming

SWX-951 SERIES
LINE VOLTAGE

Series Downloads

Instructions

Overview

SENSORWORX wireless fixture controllers switch on/off power to a connected lighting fixture as directed by wirelessly linked sensors, photocells, and wall controls. Additionally, the unit’s 0-10V dimming output simplifies applications where dimming control is required.

The SENSORWORX wireless fixture controller is intended to switch and dim a single lighting fixture. It utilizes a powerful microprocessor to optimize its switching timing, ensuring long relay life even when controlling high-inrush LED lighting. As with all SENSORWORX products, these controllers are easy to install and incorporate features that reduce contractor labor time. An elongated chase nipple with snaps for quick installation makes for a hassle-free contractor experience. All SENSORWORX products are proudly made in the USA.

 

Basic Operations

A received wireless message indicating occupancy from one or more wirelessly linked sensors will trigger the controller’s integrated relay to close. When configured for Vacancy operation, an ON switch message is required from a wirelessly linked wall station to initially trigger lights. Once closed, line voltage will flow through the relay and turn on the connected lighting load. The wireless fixture controller maintains a master time delay that is reset every time a linked sensor reports occupancy. Lights will be switched off once there hasn’t been an occupancy message reported for the duration of the time delay. If linked to a photocell, the unit receives light level readings and controls connected lighting according to its photocell operating mode.

Applications

Individual Fixture Level Control In Spaces Such As:

  • Classrooms
  • Copy Rooms
  • Open Areas
  • Small Offices
  • Conference Rooms
  • Private Restrooms
  • Hallways

Features / Wireless Fixture Controller

  • Wirelessly Links to Sensors, Photocells, & Wall Stations

  • Links in Seconds up to 50 Remote Devices

  • Intended to Switch a Single Lighting Fixture (1A maximum)

  • Electronically Timed Switching (i.e. Zero Crossing) Ensures Long Relay Life

  • Integrated Test/Programming Button

  • 0-10V Dimming Output for Partial On & Partial Off Operation

  • Configurable Time Delays and Operational Modes (e.g. Occupancy/ Vacancy)

  • Configurable Daylight Harvesting & Photocell Modes

  • Configurable Dimming Trim Levels & Fades Rates

  • Plenum Rated (UL 2043)

Specifications

Physical

SIZE
3.00” H x 2.25” W x 1.88” D
(7.62 cm x 5.72 cm x 4.78 cm)

WEIGHT
4.80 oz.

COLOR
Blue

MOUNTING
1/2” Knockout

TEST / PROGRAMING BUTTON

LED STATUS INDICATOR
Bi-color White & Blue

Operation

OPERATING MODES
Occupancy & Vacancy
Partial On/Off
Daylight Harvesting
On/Off/Inhibit Photocell

TIME DELAY OPTIONS
1, 5, 10, 15, 20, 30 min

Environmental

OPERATING TEMP
32°F to 122°F
(0°C to 50°C)

RELATIVE HUMIDITY
0-95% Non-Condensing
Indoor Use Only

Wireless

RANGE
80’ line of sight w/o obstruction
40’ with obstruction (walls/floors)

FREQUENCY
915 MHz ISM Band

WIRELESS LINKING
Simple 3 sec. Push Button Process

SECURITY
All Wireless Data is Encrypted

Code Compliance

These power packs can be used to
meet ASHRAE 90.1, IECC, & Title 24
energy code requirements

Electrical

OPERATING VOLTAGE
120-277 VAC
Single Phase, 50/60 Hz

LOAD RATINGS
1A @ 120-277 VAC switching max
No more than 3 drivers or ballast
Relays use zero-cross switching

LOAD TYPES
LED Driver
Magnetic Ballast
Electronic Ballast,
Tungsten

DIMMING LOAD
6 mA, of 0-10 VDC ballasts or drivers
(compliant with IEC 60929 Annex E.2)

ESD IMMUNITY
Tested to withstand electrostatic discharge
without damage or memory loss

Wiring Diagrams

Standard Wiring

Installation Options

Wireless Linking (Pairing)

Linking a wireless fixture controller to a wireless sensor, photocell, or remote wall station is quickly done via the following procedure:

Step 1. Enter learn (pairing) mode by holding down the controller’s button for 3 seconds until the LED starts alternating white then blue, then release.

Step 2. At the sensor, photocell, or remote wall station, hold down the programming button for 3 seconds until the LED starts alternating white then blue. Releasing will link the device with the wireless fixture controller in learn mode (see note 1 below). The lighting load being controlled will also be toggled off/on as a visual indication of success.

Step 3. Repeat step 2 to link additional devices.

Step 4. When all devices have been linked, exit learn mode on the fixture controller by pressing the button 1 time. Learn mode will also be automatically closed after 15 minutes of no new devices being linked.

Note 1: When in learn mode, the alternating LED colors on the fixture controller will periodically pause and blink out the total number of linked devices. There will be no blinks during the pause until the first device is linked.

Ordering Info

EXAMPLE MODEL # SWX-951-D1
PRODUCT
SWX–Power Pack951–D1Wireless Fixture Controller, 1A @ 120-277 VAC with 0-10V Dimming Output

Compatible Wireless Products

Wireless Dimmer & Switch

These stylish and intuitive wall stations are designed for a 10 year battery life.

Wireless Ceiling Sensors

Available with either PIR and Dual Tech. occupancy detection, these wireless sensors can be paired with a load controller in seconds.

Wireless Wide View Sensors

With five contractor friendly mounting methods, locating a sensor in a corner has never been easier.

Design by DZYNR   |  ©2024 BLP Technologies, Inc. All Rights Reserved.