Wireless Remote Switch
& Dimmer

SWX-854 & 852 SERIES
BATTERY POWERED

Series Downloads

Instructions

Overview

​The SENSORWORX® remote dimming and on/off wall stations are battery powered devices that provide manual operation of wirelessly controlled lighting. These attractive wall stations greatly reduce total installation time and wireless pairing fuss. Requiring just a few seconds per device, SENSORWORX wireless sensors can be linked to one or more wireless load controllers (such as the SWX-851 wireless wall switch, or a SWX-950 series wireless power pack). Additionally, these devices can be configured to work together with other wireless or wired wall stations to provide dimming and switching control from multiple locations.

Applications

Adding a wireless remote wall switch to a room controlled by a wireless power pack (SWX-950) and a wireless sensor (e.g. SWX-201-B) enables code compliant vacancy (manual on) operation. When linked with a wireless dimming power pack (SWX-950-D2), a remote wireless dimmer is perfect for providing user control of 0-10V dimmable lighting. Additional remote dimmer switches can be linked enabling user control from multiple locations. Linking a remote wireless switch to a wireless wall switch load controller (SWX-851) enables 3-way user control as well.

  • Classrooms
  • Open Areas
  • Conference Rooms
  • Hallways
  • Small Offices
  • Copy Rooms
  • Private Restrooms
  • Break Rooms

Features / Wireless Switches & Dimmers

  • Pairs in Seconds with Wireless Controllers

  • 10 Year Battery Life Design

  • Decorator Style Fits Common Wall Plates (not included)

  • Matches Styling of other SWX Sensors & Wired Wall Stations

  • Enables Multiway Switching & Dimming (e.g., 3-way, 4-way)

  • Intuitive Operation

Specifications

Electrical & Wireless

BATTERY TYPE
Requires one CR123A Lithium Battery
(provided in box)

BATTERY LIFE
Designed for 10 Year Life
Non-Volatile Memory
(saves all settings regardless of battery state)
Blink Warning @10% Life

RANGE
80’ line of site w/o obstruction (walls)
40’ with obstruction (walls/floors)

FREQUENCY
915 MHz ISM Band

WIRELESS LINKING
Simple 3 sec. Push Button Process

SECURITY
All Wireless Data is Encrypted

Physical

SIZE
2.74”H x 1.68”W x 1.39”D
(6.96 x 4.27 x 3.53 cm)
Fits Decorator Switch Plate Opening

WEIGHT
2.5 oz

MOUNTING
Single Gang Switch Box

Environmental

OPERATING TEMP
32°F to 122°F
(0°C to 50°C)

RELATIVE HUMIDITY
0-95% Non-Condensing, Indoor Use Only

Misc

COMPATIBLE LOAD CONTROLLERS
SWX-851 Wall Switch
SWX-950 Series Power Packs

CODE COMPLIANCE

These power packs can be used to meet ASHRAE 90.1, IECC, & Title 24 energy code requirements

Operation Notes

  • Wireless remote switches and dimmers only transmit when a button is being pressed.

  • The unit’s blue LED will light only when a button is pressed.

  • The dim up and dim down buttons may be held down to increase dimming rate.

Battery Information

  • The switch/dimmer runs on one CR123A Lithium Battery (included).

  • Install battery prior to mounting. Polarity is indicated on the battery compartment door.

  • If the unit’s battery life reaches 10%, the LED will rapidly blink blue after every button press.

  • Replacement batteries are available at most retailers or home centers where batteries are sold or from SENSORWORX.

Wireless Linking (Pairing)

Pairing a remote dimmer/switch with a wireless wall switch load controller or power pack load controller is quickly done via the following procedure:

Step 1. Enter pairing mode by holding down the wireless load controller’s button for 3 seconds until the LED starts alternating white then blue.

Step 2. At the battery powered remote dimmer/switch, hold down the ON button for 3 seconds until the LED starts alternating white then blue. Releasing will pair the device with the controller in pairing mode (see note 1 below). The lights will toggle once as confirmation.

Step 3. If additional remote dimmers or switches need to be linked, repeat step 2.

Step 4. When all devices have been paired, close pairing mode on the wireless load controller by pressing the button 1 time. Pairing will also be automatically closed after 15 minutes of no new devices being linked.

Note 1: When in pairing mode, the alternating LED colors on the wireless load controller will periodically pause and blink out the total number of paired devices. There will be no blinks during the pause until the first device is linked.

Installation Options

Designed to mount in 1-gang wall box with 3.28” hole spacing. Units can also share multiple gang wall boxes with other devices.

Ordering Info

EXAMPLE MODEL # SWX-854-B-WH
MODEL #DESCRIPTIONCOLOR
SWX–854–BWireless Remote Dimming & On/Off Wall Station, Battery PoweredWhite–WH
SWX–852–BWireless Remote On/Off Wall Station, Battery PoweredIvory–IV
Light Almond–LA
Gray–GY

*WALLPLATE NOT INCLUDED

ACCESSORY PART #COLORPACKAGE COUNT
SWX–199Single Gang Wall PlateWhite–WH10 Pack–J10
Ivory–IV
Light Almond–LA
Gray–GY

Compatible Wireless Products

Wireless Ceiling Sensors

Available with either PIR and Dual Tech. occupancy detection, these wireless sensors can be paired with a load controller in seconds.

Wireless Wall Switch

This intuitive wall switch load controller requires no neutral connection or minimum load to operate.

Wireless Power Packs

These load controllers switch a full lighting or plug load, and are available with optional 0-10V dimming.

Design by DZYNR   |  ©2024 BLP Technologies, Inc. All Rights Reserved.