Wireless Remote Dual Dimmer/Switch
SWX-85x-2P SERIES
BATTERY POWERED
Series Downloads
Overview
The SENSORWORX® wireless dual dimmer and switch provide remote manual operation of two wirelessly controlled lighting zones. These attractive single-gang wide wall stations are powered by a single battery and require just a few seconds per device to wirelessly configure. They can be easily linked to one or more wireless load controllers (such as the SWX-851 wireless wall switch, SWX-950 series wireless power pack, or SWX-874 phase dimmer). Additionally, these devices can be applied with other wireless or wired wall stations to provide dimming and switching control from multiple locations.
Applications
- Classroom
- Open Areas
- Conference Room
- Hallway
- Small Office
- Copy Room
- Private Restroom
- Break Rooom
Features / Wireless Remote Dual Dimmer/Switch
-
Dimming & On/Off Control of Two Wireless Zones in a Single Gang Device
-
Pairs in Seconds with Wireless Load Controllers
-
10-Year Battery Life Design
- Decorator Style Fits Common Wall Plates (not included)
- Matches Styling of other SWX Sensors & Wired Wall Stations
- Enables Multiway Switching & Dimming (e.g., 3-way, 4-way)
Specifications
Electrical & Wireless
BATTERY TYPE
Requires one CR123(A) Lithium Battery (provided in box)
BATTERY LIFE
Designed for 10 Year Life
Non-Volatile Memory (saves all settings regardless of battery state)
Blink Warning @10% Life
RANGE
80’ line of site w/o obstruction (walls)
40’ with obstruction (walls/floors)
FREQUENCY
915 MHz ISM Band
WIRELESS LINKING
Simple 3 sec. Push Button Process
SECURITY
All Wireless Data is Encrypted
Physical
SIZE 2.74”H x 1.68”W x 1.39”D
(6.96 x 4.27 x 3.53 cm)
Fits Decorator Switch Plate Opening
WEIGHT
2.5 oz
MOUNTING
Single Gang Switch Box
Environmental
OPERATING TEMP
32°F to 122°F (0°C to 50°C) – Standard
-40° F/C (with -HE Option)
RELATIVE HUMIDITY
0-95% Non-Condensing,
Indoor Use Only
CODE COMPLIANCE
These switches can be used to meet ASHRAE 90.1, IECC, & Title 24 energy code requirements.
Wireless Linking (Pairing)
Pairing a remote dimmer/switch with a wireless wall switch load controller or power pack load controller is quickly done via the following procedure:
Step 1. Enter pairing mode by holding down the wireless load controller’s button for 3 seconds until the LED starts alternating white then blue.
Step 2. At the battery powered remote dimmer/switch, hold down the ON button for 3 seconds until the LED starts alternating white then blue. Releasing will pair the device with the controller in pairing mode (see note 1 below). The lights will toggle once as confirmation.
Step 3. If additional remote dimmers or switches need to be linked, repeat step 2.
Step 4. When all devices have been paired, close pairing mode on the wireless load controller by pressing the button 1 time. Pairing will also be automatically closed after 15 minutes of no new devices being linked.
Note 1: When in pairing mode, the alternating LED colors on the wireless load controller will periodically pause and blink out the total number of paired devices. There will be no blinks during the pause until the first device is linked
Installation Options
- Designed to mount in 1-gang wall box with 3.28” hole spacing.
- Units can also share multiple gang wall boxes with other devices.
Battery Information
-
The switch/dimmer runs on one CR123(A) Lithium Battery (included).
-
Install battery prior to mounting. Polarity is indicated on the battery compartment door.
-
If the unit’s battery life reaches 10%, the LED will rapidly blink blue after every button press.
-
Replacement batteries are available at most retailers or home centers where batteries are sold or from SENSORWORX.
Operation Notes
- Wireless remote switches and dimmers only transmit when a button is being pressed.
- The unit’s LED (top or bottom) that is associated with the zone being controlled will light blue when a button is pressed.
- The dim up and dim down buttons may be held down to increase dimming rate.
- There are always 20 equal steps of dim level (voltage) adjustment from high trim to low trim (or reverse) when using a SWX-854-2P-B wireless remote dimmer.
Ordering Info
EXAMPLE MODEL # SWX-854-2P-B-WH
| PRODUCT | DESCRIPTION | COLOR | OPTIONS | |||||
|---|---|---|---|---|---|---|---|---|
| SWX– | 852-2P-B | Wireless Remote 2-Zone On/Off Wall Station, Battery Powered | White | –WH | Low Temp / High Humidity | –HE | ||
| 854-2P-B | Wireless Remote 2-Zone Dimmer Wall Station, Battery Powered | Ivory | –IV | |||||
| Light Almond | –LA | |||||||
| Gray | –GY | |||||||
| Red | –RD | |||||||
| Black | –BK |
| ACCESSORY | DESCRIPTION | COLOR | PACKAGE COUNT | |||||
|---|---|---|---|---|---|---|---|---|
| SWX– | 199 | Single Gang Wall Plate | White | –WH | 10 Pack | –J10 | ||
| Ivory | –IV | |||||||
| Light Almond | –LA | |||||||
| Gray | –GY | |||||||
| Red | –RD | |||||||
| Black | –BK |
Related Products
Wireless Phase Dimmer
For phase dimming from multiple locations, utilize the wireless version of the phase dimmer.
Wall Switch Sensor w/ Dimming
Occupancy sensing and 0-10V dimming in one sleek and shallow wall switch decorator device.
Line Voltage Switch w/ 0-10V Dimmer
This line powered dimmer is a simple solution for adding 0-10V dimming control to a space
