Line Voltage Dimmer (0-10V)

SWX-823 SERIES

Series Downloads

Datasheet

Media Assets

Instructions

English

Español

Overview

The SENSORWORX line voltage wall switch & 0-10 volt dimmer provides a stylish solution for spaces where manual dimming control is required. Designed with contractors in mind, the unit is significantly shallower than typical dimmers, resulting in less crowded wall boxes. Additionally, versatile wiring enables usage with or without a neutral connection. For dimming adjustment, intuitive raise and lower buttons are present in addition to the on/off button. Five vertically stacked LEDs are provided to indicate the current dimming level. Configurable dimming parameters include High/Low Trims, Turn on Levels, and Curve Types. This dimmer also matches the SENSORWORX family of wall switch occupancy sensors and 0-10V dimming wall switch sensors.

Applications

Line voltage switches with integrated 0-10V dimming control provide the ability to meet manual control energy code requirements as well as to take full advantage of the dimming capabilities of many LED fixtures. Additionally, task tuning requirements (i.e. capping the maximum light output of a fixture) can also be achieved with this stand-alone dimmer unit.

Private Office
Open Office
Conference Room
Classroom
Storage Room
Break Room

Features / Line Voltage Switches

Electrical Features

Accommodates Neutral (3-Wire) and No-Neutral (2-Wire) Installation
Electronically Timed Switching Ensures Long Relay Life

Works both Standalone and with 3-Way Switches
Meets NEC Guidelines for Current Leakage

Physical Features

Enclosure is 25-40% Shallower than Other Dimmers (< 1” Depth into Wallbox)
Self-Grounding Mounting Strap

Modern Look and Intuitive Easy-Tap Buttons for On/Off, Raise, & Lower
Settings are Adjustable Without Removing Cover Plate

Operational Features

5 LED Dimming Level Indication
Blue Locator LED when Lights are Off

Configurable Dimming Parameters including High/Low Trims, Turn on Levels, and Curve Types

Specifications

Physical

SIZE
2.74”H x 1.68”W x 1.39”D
(6.96 x 4.27 x 3.53 cm)
Not Including Mounting Strap
<1” Wallbox Mounting Depth

DEPTH IN WALL
0.94” (23.88 mm)

WEIGHT
4.5 oz

MOUNTING
Single Gang Switch Box

Electrical

OPERATING VOLTAGE
120-277 VAC SINGLE PHASE, 50/60 Hz

LOAD RATINGS
MAX: 800W @ 120VAC
1200W @ 277VAC
MIN: None

LOAD TYPES
LED Driver/Lamps
CFL, Electronic/Magnetic Ballasts (Fluorescent)
Tungsten (Incandescent)

DIMMING COMPATIBILITY
0-10 VDC ballasts or drivers compliant
with IEC 60929 Annex E.2

DIMMING LOAD
50 mA maximum (sink only)

Environmental

OPERATING TEMP
32°F to 122°F
(0°C to 50°C)

RELATIVE HUMIDITY
0-95% Non-Condensing, Indoor Use Only

Operation Settings

The one button switch has configurable settings for its LED operation. The three button switch also has several dimming parameters that can be adjusted to accommodate different applications or user preferences.

High-End & Low-End Trim

High-end trim enables energy saving task tuning by setting a maximum level (100%-50%, or Custom) that which users are allowed to raise lights
Low-end trim sets a minimum level that which users are allowed to lower lights (0%-50%, or Custom)

Turn On/Turn Off Dimming Operation

Lighting turns on to last user level or a preset level (100%, 50%, or custom)
Switch can turn off lighting by switching off power (by opening relay) or dimming below electronic off level
Lighting can also be held at low-end trim level during off state

Fade On/Fade Off Rates

Adjustable time for level to ramp up to turn-on level (0.75 sec, 1.5 sec, 3 sec, 5 sec, or 15 sec)
Adjustable time interval for level to ramp down to off (0.75 sec, 1.5 sec, 3 sec, 5 sec, or 15 sec)

Dimming Curve

The dimming curve defines how dimmers adjust their voltage output in response to button commands
Linear (default), Square Law, Logarithmic

LED Functionality

5 White LED(s) show level when lights are on
Blue LED serves as a switch locator when lights are off
LED functionality can be disabled

Wiring Diagrams

Unit works both in installations where Neutral connection is available as well as installations where only Ground connection is present.
If no neutral is present, remove the white sleeve from the wire & connect the now Green/Yellow wire to Ground.
Note, either the white wire or green/yellow wire must be connected. The all green wire is just for safety.

Standalone Wiring

3-Way Wiring

Neutral to Ground Conversion Detail

The white wire has a removable sleeve which reveals a green/yellow wire

Installation Options

Ordering Info

EXAMPLE MODEL # SWX-823-WH

	PRODUCT	DESCRIPTION	COLOR*		PACKAGE COUNT
SWX–	823	Line Voltage Switch & Dimmer (0-10V)	White	–WH	Single Pack	Blank
			Ivory	–IV	10 Pack**	–J10
			Light Almond	–LA
			Gray	–GY

* WALLPLATE NOT INCLUDED
** THE CONTRACTOR PACK OPTION (-J10) REDUCES JOB SITE WASTE AND INVENTORY TIME